Skip to content
  • There are no suggestions because the search field is empty.

Magnasonic Jewelry Cleaner Frequently Asked Questions

Table Of Contents:

picture_as_pdf_50dp_1F1F1F_FILL0_wght400_GRAD0_opsz48Manuals, and Guides 

settings_50dp_1F1F1F_FILL0_wght400_GRAD0_opsz48First Time Setup

help_48dp_1F1F1F_FILL0_wght400_GRAD0_opsz48Frequently Asked Questions

build_circle_48dp_1F1F1F_FILL0_wght400_GRAD0_opsz48Troubleshooting

 

Manuals, Guides, and Videos

Professional Ultrasonic Jewelry and Eyeglass Cleaner (MGUC500)

English

 Professional Ultrasonic Jewelry and Eyeglass Cleaner (CD2800) 

 English

 Professional Ultrasonic Jewelry and Eyeglass Cleaner (UC22) 

English

Francais 

Español

Italiano

Deustch

Polski

 

 
 

First Time Set Up

It is recommended to use the included basket if cleaning sharp objects to prevent damage to
the tank. The plastic basket can absorb some vibrations from the ultrasonic cleaner, decreasing
the machine’s cleaning ability. While the impact of the basket is small, for best performance only
use the basket when necessary.

Note: It is recommended to wait 5-10 minutes between cleaning cycles to allow the unit to cool
down and prevent overheating.

Deep Cleaning

  1. Using the ultrasonic cleaner with water will clean most items. For items that need a deeper cleaning use the below tips.

  2. Water should be added only until the object is covered. Do not fill to the MAX fill line unless it’s necessary to cover the object.

  3. A very small amount of jewelry cleaner concentrate or mild dishwasher detergent can be added to the water for additional cleaning power.

    Note: Ensure the detergent is non-corrosive and safe for contact with skin. Do not use with Acetone.

  4. If dirt and grime remain after cleaning, then a cloth or soft brush can be used to help loosen it before running it through another cleaning cycle in the ultrasonic cleaner.

Frequently Asked Questions

Items that CAN be cleaned

diamond_50dp_1F1F1F_FILL0_wght400_GRAD0_opsz48Jewelry - necklaces, bracelets, rings, earrings, body jewelry. Silver items that have dirt accumulation. See below for tarnish cleaning instructions.

eyeglasses_2_50dp_1F1F1F_FILL0_wght400_GRAD0_opsz48Glasses & Watches - eyeglasses (with no lens coatings, sunglasses, waterproof watches, watchbands.


self_care_50dp_1F1F1F_FILL0_wght400_GRAD0_opsz48Hygiene Items - electric shaver heads, toothbrushes, dentures, razor blades.

 

stylus_fountain_pen_50dp_1F1F1F_FILL0_wght400_GRAD0_opsz48Stationary - pen-heads, seals, rubber stamps.

 

flatware_50dp_1F1F1F_FILL0_wght400_GRAD0_opsz48Other Items - tools, watch parts, coins, keychains, valves, machine nozzles, badges, instruments,  filters, & kitchen utensils.

Items that CANNOT be cleaned

Glasses/sunglasses with pre-existing scratches or cracks in the coating.

Jewelry containing loose or soft/porous stones such as pearls, emeralds, amber, and opal.

NOTE: Please consult your local jeweler if you are unsure about whether or not you should use the  ultrasonic cleaner on your specific type of jewelry.

Cleaning tarnished silver

While your ultrasonic cleaner excels at remove dirt and grime, tarnish is caused by exposure to oxygen over time and bonds to silver. To remove tarnish, physical polishing of the item is required after ultrasonic cleaning.

What you need:

1. Ultrasonic Cleaner

2. Dish Soap

3. Warm Water

4. A Microfiber Cloth

TIP: If you are unable to remove the tarnish with soapy water you can also use toothpaste and water on the cloth instead.

Cleaning Steps:

1. Use the Ultrasonic Cleaner to remove dirt and grime

2. Mix a small amount of dish soap with the warm water in a separate bowl

3. Dip the microfiber cloth into the soapy water

4. Rub the silver with the wet cloth to remove the tarnish

5. Rinse the silver item in cold water

6. Dry the item with a soft cloth

7. After removing the tarnish the last step is to buff the silver with another dry soft cloth to restore it’s shine

Troubleshooting

No power

  1. UC22 only: Ensure the power cable is inserted firmly into the back of the cleaner.

  2. Unplug the cleaner from power for 30 seconds.

  3. Reconnect the cleaner to power.
  4. Check for power.